JCM Part No . 960 - 000053R _ Rev . 6 © 2007, JCM - American Corporation i x AD - 02™ Bill Acceptor Series   List of Figures Continued Page Figure 4 - 33 Validator Drive Motor Removal ....................................................... 4 - 10 Figure 4 - 34 Course Guide Removal ................................................................. 4 - 10 Figure 4 - 35 Timing Belt Removal ..................................................................... 4 - 10 Figure 4 - 36 Dispense/Reject Shaft Removal ..................................................... 4 - 11 Figure 4 - 37 Dispense/Reject Motor Disconnect ................................................ 4 - 11 Figure 4 - 38 Validator Drive Motor Removal ....................................................... 4 - 11 Figure 4 - 39 Removing Branch Solenoid ............................................................ 4 - 11 Figure 4 - 40 Dispensing Unit Drive Belt Removal ................................................ 4 - 12 Figure 4 - 41 Stacking Pulley #1 Parts Removal .................................................. 4 - 12 Figure 4 - 42 Transfer Guide 6 Removal ............................................................. 4 - 12 Figure 4 - 43 Entrance Roller Removal ................................................................ 4 - 13 Figure 4 - 44 Rubber Roller Removal ................................................................. 4 - 13 Figure 4 - 45 Connector & Harness Removal ....................................................... 4 - 13 Figure 4 - 46 Expanded Stacker Section Removal ............................................... 4 - 13 Figure 4 - 47 Stacking Pulley #1 Parts Removal .................................................. 4 - 14 Figure 4 - 48 Discharge Motor Plug Disconnect ................................................... 4 - 14 Figure 4 - 49 Stacker Discharge Motor Removal .................................................. 4 - 14 Figure 4 - 50 Drive Shaft #1 Disassembly ........................................................... 4 - 15 Figure 4 - 51 Drive Shaft #1 Removal .................................................................. 4 - 15 Figure 4 - 52 Transfer Drive Shaft Removals ...................................................... 4 - 15 Figure 4 - 53 Table Unit Disassembly ................................................................. 4 - 16 Figure 4 - 54 Table Unit Removal ....................................................................... 4 - 16 Figure 4 - 55 Transfer Roller & Rubber Roller Shaft Disassembly ......................... 4 - 16 Figure 4 - 56 Switching Solenoid Removal .......................................................... 4 - 17 Figure 4 - 57 Base Unit Right Side Cover Removal .............................................. 4 - 17 Figure 4 - 58 Base Unit Right Side Cover Removal .............................................. 4 - 17 Figure 4 - 59 Base Unit Discharge Motor Removal .............................................. 4 - 18 Figure 4 - 60 Base Unit Drive Shaft Removal ...................................................... 4 - 18 Figure 4 - 61 Transfer Plate Sensor Removal ..................................................... 4 - 18 Figure 4 - 62 Transfer Motor Removal ................................................................ 4 - 18 Figure 4 - 63 Base Unit Lifter Motor Removal ...................................................... 4 - 19 Figure 4 - 64 Base Unit Left Side Cam Removal ................................................. 4 - 19 Figure 4 - 65 Lifter & Support Shaft Removal ...................................................... 4 - 19 Figure 4 - 66 Base Table Unit Removal ............................................................... 4 - 19 Figure 5 - 1 AD - 02 Bill Validator Primary Components ......................................... 5 - 1 Figure 5 - 2 AD - 02 Bill Validator System Wiring Diagram ..................................... 5 - 3 Figure 6 - 1 Download USB Cable Requirement ................................................. 6 - 1 Figure 6 - 2 AD - 02 Required Download Tools ..................................................... 6 - 1 Figure 6 - 3 AD - 02 DIP Switch & Port Location ................................................... 6 - 2